Pyronix Belle Installation Manual
The paragraph heading includes “in series” – a bit of a misnomer since only the tamper circuits are in series. The sounder and strobe trigger connections are in parallel as are the 12v supply connections when one Belle is in SCB mode. What the manufacturer says Since its launch, the Belle has been one of the industry’s success stories, offering value for money coupled with an innovative design. Due to popular demand Pyronix has now designed and manufactured a 1.5mm low carbon steel shroud for this twin piezo external sounder. For high-risk installations this provides a formidable deterrent.
Resistance to physical attack is high, with all the components sited away from the edges of the base. This can be further enhanced by the addition of an optional metal shroud. It has been designed for easy installation and maintenance, with all components easily replaced. The test link feature should appeal to installers. Finally, the Belle is sensibly priced, representing good value for money.
This communication format is capable of transmitting a great deal of detail, including individual code holders, zone number activated, abort/restores and open/close signals. By allocating a zone type to each zone number, the system is able to send a precise text message tailored to the customer’s requirements. The system uses existing ARC protocols that installers will be familiar with, including the usual 90 second delay window in which to receive an ‘abort’ signal, and a telephone check back to site before initiating any SMS message or email. The keypad user display is an illuminated LCD icon-based type, using symbols and single characters for information rather than English text. While this keeps the manufacturing cost down and may be useful for the Pyronix European market, it is disappointing to constantly need reference to an engineering manual to decode the display information.
After the base has been fixed to the wall, the lid can be parked hanging down on its own securing screw at the bottom, and the PCB cover hooked on the hinge bar at the top. The PCB cover is reasonably safe in this position but it would not need much provocation to dislodge the lid. Is it worth the risk? Wiring is straightforward. Pyronix gives a connection chart, listing the connections for a range of control panels. A test link is included on the PCB. During installation, when the standby battery is connected with the test link removed, the sounders will operate for five seconds only.
When the metal shroud is used, it is supplied along with two steel straps. The straps are used to bridge the two top base fixing screws and the two bottom ones, giving much improved base-to- wall security. The metal shroud is put in place and fixed to the wall by a 9cm screw through the base. Properly fixed, this must be one of the most secure arrangements on the market for this class of sounder. Care must be taken to clear the sounder leads and possibly the back-up battery leads away from the sides of the base, otherwise they could easily be cut when the shroud is fixed.
Pyronix Limited Quality Security Equipment Manufacturers. By using this website you are consenting to the use of cookies, please read our. Download installation manuals. Download user guides. Stay up to date with the latest products and news from Pyronix. Follow us on.
The latches are a little stiff and brittle; one of the PCB latches broke off when we removed the components. A longer tab on the end of the latch would have avoided this problem by allowing finger pressure to be used to release the latch rather than having to resort to a pair of pliers. Four mounting bosses have been recessed into the base, sufficiently deep to lift the edges 3mm clear of the wall. This improves the sound output from the two rear-facing sounders. The lid fits neatly into recesses in the base and is held securely in place by a moulded hook at the top and a single screw at the bottom. The PCB, measuring 57 x 124mm, carries the self-alarm, timing and strobe components (including the flash tube), setting links, terminal blocks and sockets for the power LEDs, sounders and tamper switch connecting plugs. The PCB quality is of a high standard.
The manuals in this section are the Installation manuals for the popular range of Pyronix control panels. PYRONIX MATRIX 4. INSTALLATION MANUAL Pdf Download. Installation Manual Software Version 5 RINS9. Connecting a Single Keypad to a Matrix 8.
The sounder and strobe trigger connections are in parallel as are the 12v supply connections when one Belle is in SCB mode. Nayak marathi serial episodes. What the manufacturer says Since its launch, the Belle has been one of the industry’s success stories, offering value for money coupled with an innovative design. Due to popular demand Pyronix has now designed and manufactured a 1.5mm low carbon steel shroud for this twin piezo external sounder. For high-risk installations this provides a formidable deterrent. The shroud is zinc-plated with an additional passivation to provide all-weather protection against corrosion. In addition, the stringent three-way tamper action on the Belle itself (back, front and loss of power) also adds to the high security specification.
The sounder and strobe trigger connections are in parallel as are the 12v supply connections when one Belle is in SCB mode. What the manufacturer says Since its launch, the Belle has been one of the industry’s success stories, offering value for money coupled with an innovative design. Due to popular demand Pyronix has now designed and manufactured a 1.5mm low carbon steel shroud for this twin piezo external sounder. For high-risk installations this provides a formidable deterrent.
In addition, a template is printed on the rear of the packaging to make wall fixing easier than using the back itself. The ease of installation has also been considered with the steel shroud which is assembled by means of a single screw, which passes through the shroud and base to screw directly into the wall. Two braces under the wall fixing screws add further stability and protection. The Belle has a panoramic strobe effect which illuminates the full bellbox and the twin piezo sounder has an output of 118dBa at one metre. The Belle has two flashing comfort LEDs which can be mounted horizontally or vertically as can the unit itself. The Belle has a selectable SAB/SCB mode enabling more than one sounder to be fitted to a system.
We called both companies to ask questions about set-up issues. Pyronix dealt with our control panel enquiries quickly and efficiently.
Wiring is straightforward. Pyronix gives a connection chart, listing the connections for a range of control panels. A test link is included on the PCB. During installation, when the standby battery is connected with the test link removed, the sounders will operate for five seconds only. The test link can then be replaced and the sounders are inoperative until the tamper switch is closed AND the 12 volt supply is connected in the control panel. During maintenance visits, the test link can be similarly employed to maintain silence, after the initial burst, until the lid tamper switch is finally closed, confirmed by a short bleep from the sounders. This is a very useful feature, since the sound output is very close to the threshold of pain.
Software Installation Manual
The Belle has a panoramic strobe effect which illuminates the full bellbox and the twin piezo sounder has an output of 118dBa at one metre. The Belle has two flashing comfort LEDs which can be mounted horizontally or vertically as can the unit itself. The Belle has a selectable SAB/SCB mode enabling more than one sounder to be fitted to a system. A free printing service is available on the generously sized 330 x 165mm lid. Overall assessment The Belle is a very neat and attractive external sounder and strobe unit.
Good Evening. I am going to be fitting an alarm for a friend, and I wish to use the existing bell box from the previous system that was fitted. The bell box is a Pyronix Belle, and the new control panel is a Honeywell/ADE Accenta Gen 4 Mini. I would like some guidance on which terminals on the panel I should connect to the bell box terminals, as I am going to use the existing cable that is in place and still connected to the bell box.
Twin alternate flashing red LEDs, visible through the lid, indicate that there is power present – either from the back-up battery, control panel or both. A fixed 15-minute cut-off timer is included to conform to the latest EU requirements. Construction The Belle enclosure consists simply of a moulded polycarbonate lid and base. The base is of complex design with a central box for the components and empty side compartments, which act as strobe lenses and also provide a protective cushion against physical attack. Latches and pins are included in the base moulding, so that all components can be changed without removing the base from the wall.
This improves the sound output from the two rear-facing sounders. The lid fits neatly into recesses in the base and is held securely in place by a moulded hook at the top and a single screw at the bottom. The PCB, measuring 57 x 124mm, carries the self-alarm, timing and strobe components (including the flash tube), setting links, terminal blocks and sockets for the power LEDs, sounders and tamper switch connecting plugs. The PCB quality is of a high standard. A transparent plastic cover protects the PCB; this must be discarded when the metal shroud is used – otherwise, the lid will not fit properly. The quality of manufacture and construction is generally good. However we found that when fitting the lid, the hook at the top had a tendency to jam under the hinge bar on the base.
In addition, a template is printed on the rear of the packaging to make wall fixing easier than using the back itself. The ease of installation has also been considered with the steel shroud which is assembled by means of a single screw, which passes through the shroud and base to screw directly into the wall. Two braces under the wall fixing screws add further stability and protection. The Belle has a panoramic strobe effect which illuminates the full bellbox and the twin piezo sounder has an output of 118dBa at one metre.
The Enforcer technical description is all contained within a single A4-sized sheet using mostly diagrammatic explanations, which again is quite adequate for a professional installer to sift out the required information. The keypad/control instructions are necessarily more comprehensive. Even though the control is deliberately factory-programmed to suit most installations straight from the box, installers will still need to make sense of the 26-page booklet to make sure everything is covered, not least because the keypad display only gives limited information by using two digit fault or event codes. The Intamac instructions and user guides are supplied separately in the ‘Home Manager’ Welcome Pack that is supplied with the Pyronix kit, consisting of a user manual, window sticker, panel stickers and general promotional literature.
I have knocked up a basic diagram (see below) of the terminals in the bell box, and the terminals in the control panel, and of how I propose to wire them up. (I have used grey in place of white for the Strobe so it can be seen on the picture).
A fixed 15-minute cut-off timer is included to conform to the latest EU requirements. Construction The Belle enclosure consists simply of a moulded polycarbonate lid and base. The base is of complex design with a central box for the components and empty side compartments, which act as strobe lenses and also provide a protective cushion against physical attack. Latches and pins are included in the base moulding, so that all components can be changed without removing the base from the wall. The latches are a little stiff and brittle; one of the PCB latches broke off when we removed the components. A longer tab on the end of the latch would have avoided this problem by allowing finger pressure to be used to release the latch rather than having to resort to a pair of pliers. Four mounting bosses have been recessed into the base, sufficiently deep to lift the edges 3mm clear of the wall.
Performance The Belle was connected and checked for correct operation. The light output from the strobe flash tube is quite impressive, particularly at night when the installer’s logo is brilliantly outlined. During daylight, light output comes mainly from the lid at an adequate level.
Performance The Belle was connected and checked for correct operation. The light output from the strobe flash tube is quite impressive, particularly at night when the installer’s logo is brilliantly outlined.
The PCB quality is of a high standard. A transparent plastic cover protects the PCB; this must be discarded when the metal shroud is used – otherwise, the lid will not fit properly. The quality of manufacture and construction is generally good.
This mode can be used to avoid overloading the control panel in multi-sounder installations. Three-way tamper protection is provided by a front and rear operated switch and power cut-off relay contacts. The loss of 12 volts from the control panel operates the twin piezo sounders in the Belle, as does the opening of a tamper switch. Surprisingly, the opening of a tamper switch does not signal back to the control panel to operate the internal sounder until the back-up battery is also disconnected. Twin alternate flashing red LEDs, visible through the lid, indicate that there is power present – either from the back-up battery, control panel or both.